车装修井机机动性及其动力性能的研究

发布时间：2018-04-20 17:33

本文选题：车装修井机 + 车架　；参考：《西安石油大学》2012年硕士论文

【摘要】：作为油田设备，修弁机必须具备1?好的机动性能和动力性能。山于车装修井机装载了修井设备，其体积和质景大大X椉樱芪宰坝诘着躺现螅宓闹匦母叨却蠓撸庑┮蛩氐贾缕浠阅苡兴贰怠Ｉ莔作业环境恶劣，道路级别较低，，车装修井机在行驶时，运载车底盘还要承受山修井作业设备质量引起的冲击载荷：在工作时运级底盘不仅承受并架起落所引起的载荷，还要承受快绳拉力，这些因素都对车装修井机提出很高的要求。井架是修井机的重要组成部分，它的承载性能对保证修井机正常工作至关重要。本文分析研究了车装修井机在移运及工作状态下的：?心坐标，并对其通过性能、S人爬坡度、纵向和横向稳定性进行了分析和研究；分析了车装修弁机井架起升液缸在(《同位W_K的受力情况，就液n(支腿的调平问题进行了研究；利用ANSYS苻限允分析软件模拟了井架及车架的强度和刚度，分析了井架在仲出状态下及移运状态下的固仃频率和振沏图，模拟分析了车架的同Yu频率及;H:振型。对修井机的机动性能及动力件能进行研究，朽助于在修井作业的整个环节中安全驾驶安全操作，对于今后车装修井机的设计和改进提供了祁应的依椐。
[Abstract]:As oil field equipment, the repairing machine must have 1? Good maneuverability and dynamic performance. Shanyuche decorates the well machine to load the workover equipment, its volume and the quality view big X to the cherry? Qi-jae dam lying down? Mousse? Do I have to worry about the mother but the midge? Masturbation? Do you think this is changing? Yi Xing? Two? The working environment is poor, the road grade is low, and the chassis of the vehicle must bear the impact load caused by the quality of the equipment for mountain workover while driving, and the chassis of the vehicle not only bears the load caused by the installation and fall, but also the load caused by the installation. Also bear fast rope tension, these factors are car decoration well machine put forward very high requirements. Derrick is an important part of workover machine, and its bearing capacity is very important to ensure the workover machine to work normally. In this paper, the analysis and study of the car decoration well machine under the moving and working state of the:? The center coordinates are analyzed and studied through the performance of climbing slope, longitudinal and lateral stability, and the stress of lifting cylinder in the front shaft of vehicle decoration is analyzed, and the leveling problem of liquid nth (leg support) is studied. The strength and stiffness of the Derrick and the frame are simulated by using ANSYS software. The frequency and vibration of the Derrick are analyzed, and the same Yu frequency and H: mode of the frame are simulated and analyzed. The research on the maneuverability and power parts of workover machine is helpful to the safe operation of driving in the whole link of workover operation, and provides the basis for the design and improvement of the car fitment well machine in the future.
【学位授予单位】：西安石油大学
【学位级别】：硕士
【学位授予年份】：2012
【分类号】：TE935

【相似文献】